This single-site module L-Band Receiver accepts input ranging from 900 to 2200 MHz with input signal power ranging from -77 to +10 dBm. The software interface provided displays amplitude vs. time, amplitude vs. frequency (spectrum), and frequency vs. time (falling raster). Control of the L-Band receiver is also available via the software interface. The receive bandwidth is software selectable from 1 to 65 MHz. Two ICE-LB2D modules can be placed on a single ICE-PIC6 card for dual channel applications using a single 8-lane, PCI-express slot.
An internal 10 MHz reference can be used by selecting the on-board 10 MHz reference or an external 10 MHz reference can be provided via an SMB connector. An SMB connector for external 1 PPS input is available. The external 1 PPS input is stored in bit 0 of a 16-bit word that is 14-bit Data MSB aligned. When used for the ICE-PIC6 DSP Card, an IRIG-B002 (DC IRIG-B) stream can be received via an SMB connector on the ICE-PIC6 card for accurate time reference.
Contents |
Features
- Input 900 – 2200 MHz
- Input Power Range: -77 dBm to +10 dBm
- Input Variable Gain Attenuator available for 80 dB of Gain
- Front End Attenuation Control: 0 - 31 dB
- Output Bandwidth: 1 MHz to 65 MHz
- Multiple Clock Source VCO driven by 10 MHz External Reference or On-Board 10 MHz Reference
- External 1PPS TTL Input
- Input Power Read Back Capabilities
- Single-site module for use with ICE-PIC6 and ICEPOD series cards and subsystems
Applications
- L-Band Receiver
- RF to IF conversion
- RF to base band conversion
- Communications
- Instrumentation
Specifications
| Functional Block Diagram | Actual L-Band Module |
|---|---|
 |
 |
Input Specifications – Signal
| Parameter | Impedance | Minimum | Typical | Maximum | Units |
|---|---|---|---|---|---|
| Example Analog input sources: Antenna, antenna w/LNA, block down converters with 1 GHz IF, L-Band distribution switch outputs, etc., within 900-2200 MHz frequency range. |
50 ohm | -77 | -20 to 0 | +10 | dBm |
| 0.5 | 2.5 | 4.0 | V p-p |
Remarks: 0-31 dB attenuator should be used to attenuate high power input down to the typical range for best performance.
Input Specifications – External Reference and PPS
| Parameter | Impedance | Minimum | Typical | Maximum | Units | Remarks |
|---|---|---|---|---|---|---|
| External Ref. - AC coupled | 50 ohm | +/- 0.5 | +/- 1.0 | +/- 2.0 | V p-p | 10 MHz |
| External 1PPS | 50 ohm | 0.5 | 2.5 | 4.0 | V p-p | External TTL Level Input |
Absolute Maximum Ratings
| Parameter | Value | Units | Conditions |
|---|---|---|---|
| Electrical | |||
| AVcc |
5.0 |
VDC |
|
| DVcc | 3.3 |
VDC |
|
| PPS Input | 0 to 4 |
Vpeak into 50ohm |
|
| External Reference Input | 0 to 4 | Vpeak into 50ohm |
|
| Analog Input Power | +10 |
dBm (50ohm ref.) |
|
| Environmental | |||
| Operating Temperature | -10 to +65 | Degrees C | |
| Storage Temperature | -40 to +85 | Degrees C | |
Warning: Operation of this module beyond any of these parameters may cause permanent damage. Exposure to absolute maximum ratings for extended periods may affect module reliability. Operation of the module beyond these specified parameters voids the factory warranty.
Connectors
| Connector | Manufacturer | Part Number | Description | J-Number |
|---|---|---|---|---|
| Trigger In | Digi-Key | 131-1701-37 | Rt. Angle SMB Connector | J3 |
| Power Connection | Standard 2-pin Header | J5 | ||
| Standoff (2 each) |
Physical Connection | |||
| Data (J4) | Samtec | QSE-020-01-F-D-A | 40-Pin Connector |
ICE Interface Cables
| ICE-CAB-SB5 (for J2, J3) | 5 ft. BNC to SMB cable |
| ICE-CAB-SMA (for J1) | 5 ft. BNC to SMA cable |
Connectors Diagram
Pricing and Status
This model is in production and may be purchased for the price of $2,750.00 per unit.